Pavement reflectors

aluminium marking nail
Ø100 mm, shaft:60 mm

Extremely durable road surface reflector (Cat's eye) made of aluminum.
– dimensions: 100x100 mm
– weight: 0.4 kg
– material: aluminum
– color: silver
– fastening: The anchor leg is glued to asphalt or concrete with a two-component adhesive
– operating temperature range -30°C-/+60°C
– high visibility: 1+1 reflectors (Cat-eyes)

The blue wildlife warning reflector with prismatic tape is a modern and highly effective solution designed to prevent animal-vehicle collisions on roads and highways. The headlights of an approaching vehicle strike the reflector, which redirects the light outwards at a 90-degree angle into the roadside terrain (forest or ditch). This creates a continuous optical "light fence" that warns animals of impending danger and deters them from crossing while a vehicle passes. Since the color blue is virtually non-existent in nature, wild animals perceive it as a threat, while drivers are never distracted or blinded.

Ideally suited for rural roads, highway sections cutting through forested areas, and other critical high-risk locations where wildlife crossings pose a significant threat to traffic safety.

– dimensions: 215x85 mm
– material: heavy-duty, weather-resistant, and UV-protected plastic (polycarbonate/ASA), high-intensity microprismatic reflective tape
– color: black
– installation: quick and easy mounting with screws directly onto roadside delineator/marker posts at vehicle headlight height
– compliance: complies with road safety and environmental protection standards
– reflector color: blue

Extremely durable road surface reflector (Cat's eye) made of aluminum.
– dimensions: 100x100 mm
– weight: 0.4 kg
– material: aluminum
– color: silver
– fastening: The anchor leg is glued to asphalt or concrete with a two-component adhesive
– operating temperature range -30°C-/+60°C
– high visibility: 1+1 reflectors (Cat-eyes)

Extremely durable road surface reflector (Cat's eye) made of aluminum.
– dimensions: 100x100 mm
– weight: 0.4 kg
– material: aluminum
– color: silver
– fastening: The anchor leg is glued to asphalt or concrete with a two-component adhesive
– operating temperature range -30°C-/+60°C
– high visibility: 1+1 reflectors (Cat-eyes)

Extremely durable road surface reflector (Cat's eye) made of aluminum.
– dimensions: 100x100 mm
– weight: 0.4 kg
– material: aluminum
– color: silver
– fastening: The anchor leg is glued to asphalt or concrete with a two-component adhesive
– operating temperature range -30°C-/+60°C
– high visibility: 1+1 reflectors (Cat-eyes)

Glue/granule for installing plastic cover reflectors (so-called "cat's eyes").

Hot assembly, i.e. glue granules, is heated with a gas burner or previously in a boiler.

- made of glass
- diameter 100 mm
- height from the ground after installation: 18.5mm
-> 150J
- load capacity 80T
- EN 1463-1 & 2

Can be installed in both asphalt and concrete
For example:
double paving stones,
RWS tires,
ordinary plates etc.

- made of glass
- diameter 100 mm
- height from the ground after installation: 14mm
-> 150J
- load capacity 60T
- EN 1463-1 & 2

Can be installed in both asphalt and concrete
For example:
double paving stones,
RWS tires,
ordinary plates etc.

- made of glass
- diameter 50 mm
- height of the protruding part from the ground after installation: 11mm
- 100J
- load capacity 27T
- EN 1463-1 & 2

Suitable for installation on a concrete surface.
For example:
concrete ties, (double) paving stones, tiles, etc.

ATTENTION!
Do not use on asphalt!

- made of glass
- diameter 50 mm
- height from the ground after installation: 11mm
- 100J
- load capacity 27T
- EN 1463-1 and 2

Suitable for installation on a concrete surface.
about:
concrete ties, (double) paving stones, tiles, etc.

ATTENTION!
Do not use on asphalt!

- made of glass
- diameter 50 mm
- height of the protruding part from the ground after installation: 11.5 mm
-> 150J
- Can be installed on both asphalt and concrete roads.
Also suitable for: concrete elements, curb stones, tiles, etc.

3x better light reflection than other products of the same class.

- made of glass
- diameter 75 mm
- height from the ground after installation: 17mm
-> 150J
- load capacity 60T
- EN 1463-1 & 2

Can be installed in both asphalt and concrete
For example:
double paving stones,
RWS tires,
ordinary plates etc.

The anchored retroreflective road stud is a modern road marking solution that significantly improves the visibility of road edges. It is especially effective in the dark and during rainy weather, providing drivers with better guidance on the road, which in turn enhances traffic safety.

Specifications:
Dimensions: 110x60xH17 mm, anchor H50 mm
Material: Plastic
Color: Grey
Installation: Fixed to the surface using bitumen or polyurethane adhesive. Requires drilling two holes (Ø20 mm, 55 mm deep, with 50 mm spacing).
Compliance: Complies with the EN 1463 standard
Reflector color options: White/white, white/red, red/red, yellow/yellow

Reflective road marker significantly improves the visibility of road edges. It is especially effective in the dark and during rainy weather, providing drivers with better guidance on the road, which in turn enhances traffic safety. They are ideally suited for locations where regular road paint wears out quickly, especially in curves, roundabouts, exits, and other critical areas that require special attention from the driver.

Specifications:
Dimensions: 107.5x90xH17 mm
Material: Plastic
Color: white
Installation: Fixed to the surface using bitumen or polyurethane adhesive.
Compliance: Complies with the EN 1463 standard
Reflector color options: White/white, white/red, yellow/yellow

The anchored reflective road marker is a modern road marking solution that significantly improves the visibility of road edges. It is especially effective in the dark and during rainy weather, providing drivers with better guidance on the road, which in turn enhances traffic safety. They are ideally suited for locations where regular road paint wears out quickly, especially in curves, roundabouts, exits, and other critical areas that require special attention from the driver.

Specifications:
Dimensions: 107.5x90xH17 mm, anchor H50 mm
Material: Plastic
Color: Grey
Installation: Fixed to the surface using bitumen or polyurethane adhesive. Requires drilling a hole (Ø10 mm, 55 mm deep).
Compliance: Complies with the EN 1463 standard
Reflector color options: White/white, white/red, red/red, yellow/yellow

Road marking for roundabouts and curbs
– dimensions: Ø75x25 mm
– material: plastic
– color: white
– installation: on curbs with polyurethane adhesive, which allows quick and easy installation without drilling
– visibility: 360°
– complies with EN 1463 standard
– reflector color options: white, red, yellow

Road marking for roundabouts and curbs
– dimensions: Ø75x25 mm, anchor 40 mm
– material: plastic
– color: grey
– installation: on curbs with polyurethane adhesive
– visibility: 360°
– complies with EN 1463 standard
– reflector color options: white, red, yellow

Fluorescent marking for noticing the pavement edge
glows for 12 hours
Ø50mm H8mm
the glowing feature lasts up to 20 years

- with solar battery NI-MH
- diameter 112 mm
- height from the ground after installation: 4mm
- driveable
- LEDs
- expected life of 8 years
- IP68
- recommended temperature range -20˚ > +85˚
- Charging capacity: 100% in 3 hours at 100 KLux
- Light output: 2,500 mcd

Installation: Drilling and installation, two-component adhesive.
Suitable for: asphalt, concrete, natural stones.

- Li-ion with solar battery
- diameter 80 mm
- height from the ground after installation: 6mm
- driveable, limited
- LED, 360˚
- expected life of 8 years
- IP68
- recommended temperature range -20˚ > +70˚
- Charging capacity: 100% in 3 hours at 100 KLux
- Light output: 1.000 mcd

Installation: Drilling and installation, two-component adhesive.
Suitable for: asphalt, concrete, natural stones, wood.

Pavement reflector with glass balls to mark the edges of the pavement
Ø50mm H8mm
white
non-slip surface
the reflective feature lasts up to 20 years

Mark a route or boundary in a safe and clear manner.
In addition to visual separation of pedestrians, it also provides tactile feedback to road spikes.
Simplicity needs pavements to be functional and durable.
The right construction and materials make road studs extremely suitable for public spaces. This solution offers a flexible, fast and timeless solution with endless applications.

Dimensions: 150*120mm

Teens are always available with:
• Anchor rods (M12) for gluing into the pavement.
• Warranty 5 years

Material
• Corten steel 3 mm
or
• Stainless steel 316- 3 mm

Areas of use:
• Terraces
• Parking spaces
• Crosswalks
• Smoking areas
• Road markings

Mark a route or boundary in a safe and clear manner.
In addition to visual separation of pedestrians, it also provides tactile feedback to road spikes.
Simplicity needs pavements to be functional and durable.
The right construction and materials make road studs extremely suitable for public spaces. This solution offers a flexible, fast and timeless solution with endless applications.

Dimensions: 105*60mm

Teens are always available with:
• Anchor rods (M12) for gluing into the pavement.
• Warranty 5 years

Material
• Corten steel 3 mm
or
• Stainless steel 316- 3 mm

Areas of use:
• Terraces
• Parking spaces
• Crosswalks
• Smoking areas
• Road markings

Mark a route or boundary in a safe and clear manner.
In addition to visual separation of pedestrians, it also provides tactile feedback to road spikes.
Simplicity needs pavements to be functional and durable.
The right construction and materials make road studs extremely suitable for public spaces. This solution offers a flexible, fast and timeless solution with endless applications.

Dimensions: 50*60mm

Teens are always available with:
• Anchor rods (M12) for gluing into the pavement.
• Warranty 5 years

Material
• Corten steel 3 mm
or
• Stainless steel 316- 3 mm

Areas of use:
• Terraces
• Parking spaces
• Crosswalks
• Smoking areas
• Road markings

Mark a route or boundary in a safe and clear manner.
In addition to visual separation of pedestrians, it also provides tactile feedback to road spikes.
Simplicity needs pavements to be functional and durable.
The right construction and materials make road studs extremely suitable for public spaces. This solution offers a flexible, fast and timeless solution with endless applications.

Dimensions: 70*60mm

Teens are always available with:
• Anchor rods (M12) for gluing into the pavement.
• Warranty 5 years

Material
• Corten steel 3 mm
or
• Stainless steel 316- 3 mm

Areas of use:
• Terraces
• Parking spaces
• Crosswalks
• Smoking areas
• Road markings

Roadstuds: durable, unbreakable, solid body and cat eyes.
– size: 100x100x21 mm
– weight: 0,4kg
– material: aluminium (AL)
– colour : silver
– fixing to concrete with screw kit and epoxy gluing for stud type (bolt to set in concrete, ø 20 mm, L 50 mm)
– operating temperature range: -20°C-/+60°C
– high visibility 3+3 Cat-eyes

Road stud: durable, unbreakable, solid body and reflectors
– size: 100x220x32 mm
– weight: 0,24 kg
– material: PPC
– color: yellow
– fixing to concrete with screw kit
– operating temperature range: -20°C-/+60°C
– high visibility 3+3+3 reflectors

Wide range to use: on roads, streets, parking lots, pedestrian crossing, traffic islands, shoulder lines, tunnels, subways and all blind points required to mark.

Roadstuds: durable, unbreakable, solid body and cat eyes.
– size: 120x120x28 mm
– weight: 0,3 kg
– material: aluminium (AL)
– colour : silver
– fixing to concrete with screw kit and epoxy gluing for stud type
– operating temperature range: -20°C-/+60°C
– high visibility 2+2 Cat-eyes

Roadstuds: durable, unbreakable, solid body and reflectors
– size: 120x120x28 mm
– weight: 0,18 kg
– material: PP
– colour : yellow
– fixing to concrete with screw kit
– operating temperature range: -20°C-/+60°C
– high visibility 2+2+2 reflectors