Ø26,9 mm

Short Tee. Provides a perpendicular connection between two tubes. Top fitting for straight and level railing uprights. This fitting cannot be used to join a horizontal tube within the fitting.

Short Tee 45°. Forms a connection between two tubes at an angle of 45°.

Long Tee. Similar to Type 2. This fitting can be used where a join is required in the horizontal tube.

Elbow 90°. Elbow joint fitting used as an end fitting for the top rail.

Straight Coupling. Joint clamp for tubes of the same diameter. Do not use for heavy vertical loads. Alternative clamp is Type 9 used as an internal spigot.

Tubefitting sleeve with gradient. Connecting clamp for tubes of unequal diameter.

Internal Coupling. A streamlined flush joint in two tubes of the same size. Wall thickness must be 3.2 mm. Do not apply direct loads to this joint.

Wall Flange. This clamp is used on structures where positional fixing is required. Do not use as a base flange to support guard railings or similar systems.

Round base plate open. This tubefitting is suitable for constructions where the pipe has to run through. Suitable for the use of e.g. intermediate shelves.

Railing Base Flange. Strong baseplate to support vertical post. Vertical wide rib with two setscrews increases the strength of the clamp. The fixing holes in the base flange should be in line with the applied load.

Round base plate with inlay (SET). Excellently suitable as rod holder. Supplied as a set (left and right version). After you have placed the round foot plates, you can simply insert the tube. Also suitable for temporary removal of a passageway, where the tube can be removed easily and quickly.

Three Way Top Corner. Corner joint (90°) clamp used for top rail corners and any other rectangular system.

Corner With Trough Tube 90°. Often used on intermediate rail corners to match Type 18, tube passes through the clamp.

Add-On Corner With Trough Tube 90°. Openable corner connection (90°), with the vertical tube running through the clamp.

Two Socket Cross. 90° joint clamp between the middle rail and an upright on railings.

Side Outlet Tee. 3-direction clamp used to fix uprights with 3 horizontal tubes that are perpendicular to each other. Upright tube passes through the clamp.

Four Socket Cross. 4-direction clamp used to fix uprights with 4 horizontal tubes that are perpendicular to each other. Upright tube passes through the clamp.

Crossover 90°. Crossover clamp (90°). Used for long tube intersections with uprights where decreasing cutting cost and increasing strength of the system with continuity of the tube is desired.

Combi Socket Tee and Cross. Frequently used for racking. The upright hole can be changed according to the application. For shelved racking, the outside hole is upright, and for pallet racking the upright is inside the carrying rails.

Clamp-On Tee. Used for adding to and modifying an existing structure.

Clamp-On Crossover. 90° crossover joint fitting for adding to an existing structure.

Handrail Support. For fixing handrails and structures to walls.

Type 35, Handrail Support, open. For fixing handrails and structures to walls.

Male Single Lug. Used with Type 42 for swivel fittings, also used for fixing panels and boards.

Male Double Lug. Similar to Type 36 with two lugs on the same axis.

Male Corner Lug 90°. Similar to Type 36 with two lugs which are perpendicular to each other.

Single Swivel. Swivel fitting for variable angle fixing.

Double Swivel. Swivel fitting for variable angle fixing for two sides of the post.

Corner Swivel 90°. Swivel fitting for variable angle fixing for a corner post.

ATTENTION: The price is for one tube fitting. The figure shows a set of two fittings.

Adjustable Swivel Tee. Always used in pairs to allow angle variation between 54 and 270 degrees.

608049B = 70° - 208° (min/max angle)
608049C = 71° - 217° (min/max angle)
608049D = 97° - 270° (min/max angle)
608049E = 54° - 215° (min/max angle)