Ø60,3 mm

By default, prices are displayed without VAT. To see VAT prices, change your selection here ↑
Short Tee. Provides a perpendicular connection between two tubes. Top fitting for straight and level railing uprights. This fitting cannot be used to join a horizontal tube within the fitting.
SKU: NKL002
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 2,60 €
Short Tee 45°. Forms a connection between two tubes at an angle of 45°.
SKU: NKL003
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 5,20 €
Long Tee. Similar to Type 2. This fitting can be used where a join is required in the horizontal tube.
SKU: NKL004
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 6,40 €
Elbow 90°. Elbow joint fitting used as an end fitting for the top rail.
SKU: NKL006
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 3,10 €
Straight Coupling. Joint clamp for tubes of the same diameter. Do not use for heavy vertical loads. Alternative clamp is Type 9 used as an internal spigot.
SKU: NKL008
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 4,90 €
Wall Flange. This clamp is used on structures where positional fixing is required. Do not use as a base flange to support guard railings or similar systems.
SKU: NKL010
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 3,60 €
Railing Base Flange. Strong baseplate to support vertical post. Vertical wide rib with two setscrews increases the strength of the clamp. The fixing holes in the base flange should be in line with the applied load.
SKU: NKL012
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 8,90 €
Three Way Top Corner. Corner joint (90°) clamp used for top rail corners and any other rectangular system.
SKU: NKL018
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 4,20 €
Corner With Trough Tube 90°. Often used on intermediate rail corners to match Type 18, tube passes through the clamp.
SKU: NKL020
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 3,40 €
Two Socket Cross. 90° joint clamp between the middle rail and an upright on railings.
SKU: NKL022
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 3,70 €
Side Outlet Tee. 3-direction clamp used to fix uprights with 3 horizontal tubes that are perpendicular to each other. Upright tube passes through the clamp.
SKU: NKL024
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 4,90 €
Crossover 90°. Crossover clamp (90°). Used for long tube intersections with uprights where decreasing cutting cost and increasing strength of the system with continuity of the tube is desired.
SKU: NKL028
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 4,50 €
Reducing Crossover 90°. Used as Type 28. reduction fitting makes it possible to design structures in two different tube diameters.
SKU: NKL028V
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 7,20 €
Clamp-On Tee. Used for adding to and modifying an existing structure.
SKU: NKL032
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 5,00 €
Clamp-On Crossover. 90° crossover joint fitting for adding to an existing structure.
SKU: NKL033
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 4,50 €
Male Single Lug. Used with Type 42 for swivel fittings, also used for fixing panels and boards.
SKU: NKL036
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 2,90 €
Single Swivel. Swivel fitting for variable angle fixing.
SKU: NKL044
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 6,90 €
Swivel Base Plate (Unisize). For fixing structures to wall or floor, usually used with Type 42.
SKU: NKL050
, Qty: In Stock
, Delivery time: 1-2 nädalat
4,80 €
Swivel Base. Used for an angled wall attachment or support for an upright post.
SKU: NKL051
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 10,50 €
Groundsocket. A ground socket fitting inside the concrete for fixing upright tube. Post is retained with a locking setscrew, allowing easy insertion and removal (if necessary).
SKU: NKL054
, Qty: Out of Stock
, Delivery time: 1-2 nädalat
From 33,00 €
Single Sided Panel Clip. One-sided mesh panel clip.
SKU: NKL070
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 1,90 €
Aluminum cap used to plug the end of the tube.
SKU: NKL073
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 2,67 €
Plastic cap used to plug the end of the tube.
SKU: NKL074
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 0,56 €
Saddle Clamp. Our steel cap brackets are electrolytically galvanized and therefore rust-resistant. These so-called single-lip cover brackets are available for tube sizes 21.3 mm up to 60.3 mm. Extremely suitable for mounting blades on a tubular frame base.
SKU: NKL100
, Qty: In Stock
, Delivery time: 1-2 nädalat
From 2,20 €
Round pipe galvanized D=60.3 mm
wall thickness 2.0 mm
Max. length 7 m
wall thickness 2.0 mm
Max. length 7 m
SKU: OP60VT
, Qty: In Stock
13,00 €