Square tube fittings

Short T-piece - 25 mm. Forms a perpendicular connection between two tubes. Upper fitting for straight, horizontal railing supports. This fitting can not be used for horizontal tube connections in the fitting itself.

Short T-piece - 40 mm. Forms a perpendicular connection between two tubes. Upper fitting for straight, horizontal railing supports. This fitting can not be used for horizontal tube connections in the fitting itself.

Long T-piece. This fitting can be used where a join is required in the horizontal tube.

Long T-piece. This fitting can be used where a join is required in the horizontal tube.

Slope Elbow 90° Variable angle 0° - 11°. Elbow joint fitting used as an end fitting for the top rail up to 11°.

Angle clamp 90° - 25 mm, which is well suited for forming a 90° angle between a horizontal and a vertical pipe.

Straight Coupling. Joint clamp for tubes of the same diameter. Do not use for heavy vertical loads. Alternative clamp is Type 9 used as an internal spigot.

Straight Coupling. Joint clamp for tubes of the same diameter. Do not use for heavy vertical loads. Alternative clamp is Type 9 used as an internal spigot.

Square footplate - 25 mm. Use this clamp for positioning constructions. Do not use as a basis for supporting safety railings and the like.

Suitable for end connection.

Rectangular Base Flange. Strong baseplate to support vertical post. Vertical wide rib with two setscrews increases the strength of the clamp. The fixing holes in the base flange should be in line with the applied load.

Three-way elbow 90° - 25 mm. Angle connection clamp (90°) for corners of overheads and all other angled connections.

Three-way elbow 90° - 40 mm. Angle connection clamp (90°) for corners of overheads and all other angled connections.

Angle of continuous upright - 25 mm. Corner connection (90°), where the vertical tube runs through the clamp.

Angle of continuous upright - 40 mm. Corner connection (90°), where the vertical tube runs through the clamp.

Two Socket Cross - 25 mm. 90°- joint clamp between the middle rail and an upright on railings.

Two Socket Cross - 40 mm. 90°- joint clamp between the middle rail and an upright on railings.

Side Outlet Tee - 25 mm. 3-direction clamp used to fix uprights with 3 horizontal tubes that are perpendicular to each other. The upright tube passes through the clamp.

Side Outlet Tee - 40 mm. 3-direction clamp used to fix uprights with 3 horizontal tubes that are perpendicular to each other. The upright tube passes through the clamp.

A cross with four slots. A 4-way clamp used to attach uprights with 4 horizontal tubes perpendicular to each other. The standpipe passes through the clamp.
Suitable for square tube 25 x 25 mm

A cross with four slots. A 4-way clamp used to attach uprights with 4 horizontal tubes perpendicular to each other. The standpipe passes through the clamp.
Suitable for square tube 40x40 mm

Crossover 90°. Crossover clamp (90°). Used for long tube intersections with uprights where decreasing cutting cost and increasing strength of the system with continuity of the tube is desired.

Crossover 90°. Crossover clamp (90°). Used for long tube intersections with uprights where decreasing cutting cost and increasing strength of the system with continuity of the tube is desired.

Type 34, Handrail support - 25 mm. To attach railings and constructions to walls.

Type 34, Handrail support - 40 mm. To attach railings and constructions to walls.

Male Single Lug. Also used for fixing panels and boards.
Suitable for square tube 25 x 25 mm

Male Single Lug. Also used for fixing panels and boards.
Suitable for square tube 40x40 mm

Female Single Socket. Often used together with other brackets, such as Type 36, 38, and 40. One part of swivel fitting, not generally used alone.

Female Single Socket. Often used together with other brackets, such as Type 36, 38, and 40. One part of swivel fitting, not generally used alone.

Single Swivel. Swivel fitting for variable angle fixing.