Categories

Forklift safety systems

Forklift safety systems
Sort By:
Display: as list / as grid

By default, prices are displayed without VAT. To see VAT prices, change your selection here 

 
Wireless forklift camera, installation to the forklift fork with a magnet, rechargeable batteries, 7" screen, automatic connection, wireless signal transmission distance up to 100m, 4 input channels, possibility to connect an additional screen, single image mode and automatic periodic change, automatic channel detection; each channel can be individually set to detect the image, built-in recorder (up to 128GB Micro SD memory card), real-time recording and playback

Description: CAMERA: 756x504px, wireless, frequency 2400-2483.5MHz, IP69K - 10G - durable metal housing, 1-3m night vision, MPEG4 video format, frame rate PAL: 25fps, NTSC 30fps, delay 120ms, operating temperature -20℃ ... + 70℃, current 10-32VDC, BATTERY SET: rechargeable, 8700mAh - 31.32Wh, charging voltage 5-16V with USB cable, USB cable with wires and 240VAC power cord included, charging time 12h (5V) - 4h (12V), discharge (@160-180mA ): 12-14h, IP69K, magnetic mount, SCREEN: 7", 800x3x480px, wireless, remote control, 4 channels, 10-32VDC, max power consumption 6W, speaker 1.5W/8Ω, U-mount frame and foot included

Voltage: 10-32V
SKU: 170500012 ,   Qty: Out of Stock ,   Delivery time: 1-2 päeva
476,00 €
Collision Sentry Corner Pro is the collision warning system designed to reduce or eliminate accidents at blind corner intersections. When motion is detected on both sides of the corner, creating conditions for an accident, Collision Sentry Corner Pro sends a visual and audio alert to warn of approaching traffic.

Collision Sentry Corner Pro is easy to install, self-powered, compact, highly visible and reliable.

Loud enough to be heard within the corner zone; pitch sets it apart from other background noise
Volume can be adjusted (high/low) or turned off.
Sounds and flashes ONLY when motion is detected on both sides of the corner

Integrated, recessed magnet mounts snap on to rack for a secure, tight fit
Integrated mounting points for attaching the unit to non-magnetic surfaces
Optimal installation height is 7-9 feet

Self-powered: Standard D-cell batteries (included)
Blue light, beeping low battery indicator
Battery life tested to a minimum of 12 months

Passive infrared motion sensors
Detection zone 6-7 meters in each direction
Alert sent in ample time to take corrective action
Pre-set and ready to use
SKU: COLCEN ,   Qty: In Stock ,   Delivery time: 2 nädalat
350,00 €
The IPAS pedestrian warning chip is designed to be used in conjunction with other IPAS warning system products to reduce the risk of collisions between pedestrians and vehicles.

If a pedestrian gets too close to a forklift/vehicle on which an IPAS vehicle antenna is installed, the warning chip gives a signal either by vibration and/or sound.

Dimensions: 40 × 72 × 19.5mm
SKU: PAS-K01-0100 ,   Qty: In Stock ,   Delivery time: 2 nädalat
165,00 €
Suitable for installation in "blind corners/areas" where there is a risk of collision between vehicles and pedestrians. Warns with flashing lights and a warning sound.
Dimensions: 123x140x112mm
SKU: PAS-K01-2100 ,   Qty: Out of Stock ,   Delivery time: 3-4 nädalat
1550,00 €
The IPAS warning system is designed to reduce the risk of collisions between pedestrians and vehicles. While most similar systems work with RFID technology, the IPAS system works with ultra-wideband technology (UltraWideBand technology), which is considerably more accurate and has a larger working radius (up to 30m). A larger working radius gives drivers time to react even when moving at higher speeds.

Advantages of the IPAS system: The devices are easy to install and do not require rebuilding of vehicles. The antenna attaches using strong magnets and can be powered either by connecting directly to the vehicle's electrical system or to a cigarette lighter.
The devices work on 12/24V.
SKU: PAS-K01-1100 ,   Qty: In Stock ,   Delivery time: 3-4 nädalat
1750,00 €
TOPLINE LASER WITH KEY FOB
triggered by remote control,
auto turn off after 2 min (timer),
designed to resist heavy bumps and vibration,
robust metal body,
30sec to install – no special tools required
simple maintenance: battery charge x1 a week (2 shifts per day),
work temperature: +10..+40 °C.
CE declaration of conformity,
carriage classes: all available
high visibility in daylight
long working time – short maintenance
made in EU (Lithuania)
12 months warranty
finish: RAL1007 (could be arranged in different color)

Package contains:
TOPLINE LASER (1 unit)
remote control (2 units)
batteries (2 packs)
charger (1 unit)
user manual
SKU: TOPLINE ,   Delivery time: 4-5 nädalat